CuZn25Al6Fe3Mn3 Solid Bronze Bushing Oil Lubricated Brass Bearing Bushing
JDB-1U P10S Special High Strength Brass Solid Bronze Bearing JDB-1U P10S Special high strength Solid bronze bearing is made of high tensile brass with plain type or with oil grooves. This type of bushing is also called brass bushing bearing, C86300 solid bronze bearing, CNC turned solid bronze be...
JDB-1U P10S Special High Strength Brass Solid Bronze Bearing
JDB-1U P10S Special high strength Solid bronze bearing is made of high tensile brass with plain type or with oil grooves. This type of bushing is also called brass bushing bearing, C86300 solid bronze bearing, CNC turned solid bronze bearing,SAE430B cast bronze sliding bearing and etc.
Material
CuZn25AI5Mn4Fe3( High Strength)
Material Chemical Composition
% Cu% Pb% Sn% Zn% Fe% Ni% Al% Mn%
Min. 60.00 0.00 0.00 22.00 2.00 0.00 5.00 2.50
Max. 66.00 0.20 0.20 28.00 4.00 1.00 7.50 5.00
Oil Grooves Types
High Strength Brass Solid Bronze Bearing 0
Characteristics
●Machined cast bronze bearings offer technically and economically favorable bearings solutions.
● High load capability, low weight and good corrosion resistance.
● The tolerance is much tighter than wrapped bronze bushes.
● All kinds of oil grooves can be choosed,lubricating by oil filled in the oil grooves.
Availability
Cylindrical bronze bushing, flanged bronze bush, thrust washer and slide plate are standard fabrication.
Special designed solid metal bearing and material can be made according to your design.
Other material can be made based on your requirement.
Application
JDB-1U P10S solid bronze bearing is widely used in heavy load condition, such as the joint of grab, huge gear box and so on.
Technical Data
Material CuZn25AI5Mn4Fe3( High Strength)
Density 7.80
HB Hardness ≥250
Tensile Strength MPa ≥800
Yield Strength MPa ≥450
Elongation % ≥800
Thermal Expansion Coefficient 1.9x10*%/°C
Max. Operation Temp. -40~+300°C
Max. load MPa 75
Max. speed m/s(Dry) 0.1
Max. speed m/s(Lubricated) 0.25
Max. PV (N/mm² *m/s)(Dry) 1.65
Max. PV (N/mm² *m/s)(Lubricated) 3.25
Mouting Suggestion
Housing – Ø: Mounting bevel, min. 1,5 mm x 15-45°
Shaft: Mounting bevel, 5 mm x 15°, edges rounded
Force fitting mandrel: The application of an adequate force fitting mandrel is advisable. Grease lubrication of the outer surface may be necessary when mounting.
JDB-1U P10S Special high strength Solid bronze bearing is made of high tensile brass with plain type or with oil grooves. This type of bushing is also called brass bushing bearing, C86300 solid bronze bearing, CNC turned solid bronze bearing,SAE430B cast bronze sliding bearing and etc.
Material
CuZn25AI5Mn4Fe3( High Strength)
Material Chemical Composition
% Cu% Pb% Sn% Zn% Fe% Ni% Al% Mn%
Min. 60.00 0.00 0.00 22.00 2.00 0.00 5.00 2.50
Max. 66.00 0.20 0.20 28.00 4.00 1.00 7.50 5.00
Oil Grooves Types
High Strength Brass Solid Bronze Bearing 0
Characteristics
●Machined cast bronze bearings offer technically and economically favorable bearings solutions.
● High load capability, low weight and good corrosion resistance.
● The tolerance is much tighter than wrapped bronze bushes.
● All kinds of oil grooves can be choosed,lubricating by oil filled in the oil grooves.
Availability
Cylindrical bronze bushing, flanged bronze bush, thrust washer and slide plate are standard fabrication.
Special designed solid metal bearing and material can be made according to your design.
Other material can be made based on your requirement.
Application
JDB-1U P10S solid bronze bearing is widely used in heavy load condition, such as the joint of grab, huge gear box and so on.
Technical Data
Material CuZn25AI5Mn4Fe3( High Strength)
Density 7.80
HB Hardness ≥250
Tensile Strength MPa ≥800
Yield Strength MPa ≥450
Elongation % ≥800
Thermal Expansion Coefficient 1.9x10*%/°C
Max. Operation Temp. -40~+300°C
Max. load MPa 75
Max. speed m/s(Dry) 0.1
Max. speed m/s(Lubricated) 0.25
Max. PV (N/mm² *m/s)(Dry) 1.65
Max. PV (N/mm² *m/s)(Lubricated) 3.25
Mouting Suggestion
Housing – Ø: Mounting bevel, min. 1,5 mm x 15-45°
Shaft: Mounting bevel, 5 mm x 15°, edges rounded
Force fitting mandrel: The application of an adequate force fitting mandrel is advisable. Grease lubrication of the outer surface may be necessary when mounting.